Riding Lawn Mower Engine Cranks But Won’t Start

Riding Lawn Mower Engine Cranks But Won’t Start


Hi, Wayne here from Sears PartsDirect. Today we’re going to troubleshoot a riding
lawn mower engine that spins but won’t start when the starter motor runs. Once it’s spinning, the engine needs 3 things
to run—fuel, spark and compression. Here’s a quick test that can often eliminate
2 of those suspects right away. We’ll check to see if the engine has compression
and spark by spraying a short burst of starter fluid into the engine’s cylinder. The highly combustible starter fluid will
start the engine briefly if the cylinder gets spark and the right amount of compression. In a well-ventilated area, pull off the air
filter and spray a short burst of starter fluid into the cylinder through the carburetor’s
air intake. Now try to start the engine. If the engine doesn’t start at all, you
can skip to the next section on fuel system troubleshooting and move on to checking the
ignition system. If the engine starts briefly and then dies,
you know the spark and compression are okay, leaving you with a fuel supply problem. A dirty carburetor is usually the culprit
when the engine isn’t getting fuel. But, before you replace or rebuild the carburetor,
check these basic fuel supply issues so you don’t waste money on a part that you don’t
need. If the air filter you just pulled off is dirty,
replace it. You need a clean air filter so the right amount
of air can mix with the fuel to start the engine. If you haven’t used the mower for several
months, drain and refill the fuel tank with fresh gas. Over time, gas absorbs water and loses combustibility. In the future, if you don’t use up all the
gas before storing your riding mower for several months, add fuel stabilizer to your gas tank. A clogged fuel filter won’t allow gas to flow
to the carburetor. Replace the fuel filter if you haven’t changed
it within the last year. Here’s a video that shows you how. The fuel solenoid valve shuts off fuel to
the carburetor to prevent backfire when you kill the engine. If the wire’s disconnected, the solenoid won’t
open to allow fuel to flow to the carburetor. Check the wire harness connection on the fuel
solenoid valve. Reconnect the valve wire harness if you find
it disconnected. Check the fuel line from the fuel tank to
the carburetor for clogs or damage. Clear any clogs and replace the fuel line
if damaged. If your engine has a fuel pump, replace the
pump if it doesn’t move gas through the fuel line to the carburetor. If you found no problems when checking these
fuel system issues, then rebuild or replace the carburetor to restore the fuel supply
to your engine. If your engine didn’t start with the help
of starter fluid, check the ignition system. First, make sure you have the spark plug wire
firmly connected to the plug. Replace the ignition coil if you find damage
to the spark plug wire because the wire is part of the coil. Here’s a video that shows how. If you found no problems with the spark plug
wire, pull the wire off and remove the spark plug. Check the spark plug tip for carbon or oil
deposits that could prevent the plug from sparking. Also, check for cracks in the plug’s insulator. Replace the spark plug if the plug’s too
fouled to spark or the insulator is cracked. If the spark plug looks okay, use a spark
plug tester to see if the plug it getting current from the ignition coil. To test it, install the spark plug and connect
the boot of the tester to the spark plug. Connect the engine’s spark plug wire to the
other end of the tester. Crank the engine and see if the tester sparks. If the tester doesn’t spark, it’s likely
you need to replace the ignition coil. If the plug sparks, that means the ignition
coil is good, but the timing for the spark might be off. Here’s how the timing works on a riding mower
engine. The flywheel magnet and ignition coil control
spark timing. When the flywheel magnet passes the ignition
coil, the coil generates and sends current to the spark plug, causing the spark. The flywheel key keeps the flywheel aligned
on the engine crankshaft so the magnet passes the ignition coil at the right time. The flywheel key is a small metal rectangle
that keeps the crankshaft and flywheel aligned when you tighten the flywheel bolt. To protect expensive engine components from
damage, the flywheel key shears if a mower blade hits an object with enough force to
make the flywheel slip out of alignment with the crankshaft. If you hit a rock or stump and the engine
suddenly stops, you may have knocked off the timing by damaging or breaking the flywheel
key. A damaged flywheel key means the magnet won’t
pass the ignition coil at the right time for the spark plug to ignite the fuel to start
and run the engine. If this scenario sounds familiar because you
did hit an object while mowing and the engine stopped, remove the flywheel and check that
key. Replace the flywheel key if you find damage. Here’s a video that shows you how. If you find no problems with the ignition
system, then a compression problem could be preventing the engine from starting. Check the oil level to see if the engine is
overfilled. Drain some oil to drop it below the maximum
fill level. If the oil level is okay, pull out the spark
plug and check cylinder compression using a compression gauge. This test shows whether the piston is compressing
the air and fuel mixture in the cylinder. Connect the compression gauge to the cylinder
through the spark plug hole. Zero the compression gauge. Briefly turn the key to the start position
so the starter motor spins the engine. Check the compression reading. Most engines should measure over 40 psi of
compression. Many engines produce more than 80 psi. If cylinder compression is less than 40 psi,
the piston isn’t compressing air inside the cylinder. Keep in mind that a low compression reading
shows you that a compression problem exists, but doesn’t reveal the cause. You might need to adjust the valves or replace
the piston rings. A damaged cylinder wall can also prevent the
piston from compressing air inside the cylinder. To accurately analyze a compression problem,
have a service technician do a leak-down test on the engine. The technician will use an air compressor
and special tools to find where air leaks. Once the technician finds the cause of the
compression problem and fixes it, you can get back to mowing. I hope this video helps you out today. You can find links to the products and parts
we talked about in the video description below. Check out our other videos here on the Sears
PartsDirect YouTube channel. Subscribe and we’ll let you know when we
post new ones.

61 thoughts on “Riding Lawn Mower Engine Cranks But Won’t Start

  1. Top notch video. Thanks very much for making this. With your help, I'm pretty sure I have to replace the ignition coil on my lawn tractor.

  2. Thank you for making this series. Over the past few years, I've had to make repairs to my 2 riding mowers and wish I had these for those repairs instead of using something "close". Or reading forums, then referring to the parts diagrams. I even had the "mower doesn't crank or click" in March – a month before that video was published. 🙂

  3. Let's go back and shopping at Sears. Hopefully, the stores will survive and stay in business. Very good video from a very knowledgeable and good man. God bless!

  4. Great video. Thanks. Our mower won't run. It's running with starter fluid but won't keep going. The back fire solenoid wasn't working when i tested it with a battery. I disabled it by cutting off the pin. The float bowl isn't filling up either way. It's a new fuel pump. I can't figure out why it won't work.

  5. Thank you. Between this video and this one https://m.youtube.com/watch?v=2_H084rFdXs&rdm=2yt9l5bb&noapp=1&client=mv-google I have fixed it

  6. Best video for engine not starting I've ever seen! I learned so much. Haven't yet tried the links, but that's a great feature of your video.
    This guy is great, give him a raise!

  7. I have a 2015 T3200 Craftsman riding mower. Ran great last fall. stored in the garage for winter, pull it out today and added fresh gas to about 1/4 tank of gas already in it. Mower will turn over but not firing or trying to start.. I took the fairly new plugs out and cleaned them up with a little sand paper on both ends of the plug, it still will not fire. Any ideas what I could check for to help diagnose the problem. Thank you ahead of time for any advice you can give me. Ric

  8. Your video is very clear and helpful. Thanks for posting and do post more helpful videos, keep them coming. Thanks again.

  9. Hey I got a twin cylinder Briggs & Stratton engine that only fires on one cylinder any ideas on what it could be

  10. I have the Craftsman lawn, tractor model 247203734 that I purchased 2 years ago. I was using the other and it was working fine. After finishing mowing the lawn I stop the engine and then went to do so more yard work. I then tried to start the lawn mower to put it in the shed it would not start. The engine turns but it won't start. I check the fuel line and its fine. I replace the spark plug and it won't start. The engine just turn but won't start. Could it be the Carburetor that needs to be replaced? I'm surprised this is happening since I only have this lawn tractor for 2 years…Any help would be appreciated

  11. Great, Clearly Explained Video. No dogs, kids, or Pre Start up Stories about nonsense that Doesn’t Matter. I’ve died and gone to Trouble Shootings Tutorial Heaven. Lol. Thankyou Sir. Very Professional

  12. I'm having trouble with my Craftsman rider. It's got too much compression the starter can't spin the engine over fast enough to get it started . please let me know if you have a suggestion. Thanks

  13. This is the most comprehensive video I've seen to date! Very well done… I have a John Deere LA125 that cranks, but won't start. I've had to watch at least 20 videos posted by John Deere users and still, I haven't found my problem. I'm going to bookmark this Video for sure!

  14. Awesome explanation and troubleshooting tree best on youtube easiest to understand no nonsense to the point great video thank-you very much

  15. I have a Dixie chopper. In the morning it starts good but once it's hot it cranks to long before it starts .I just changed the choke cable and I notice that started doing this since then. Any suggestions will be appreciated

  16. I have a Craftsman T2400 riding mower only a few months old. I was cutting the grass just fine when I ran out of gas (first time I have done this). I filled the gas back up and now I can't get it to start. It cranks but won't start. I am a woman and have nobody here to help me. Is there something I should be doing? I have checked the spark plug and there was no gas in there. I see fuel in the filter, the air filter is also clean. My blades are NOT ingaged.

  17. Hi,I have a Craftsman 4 years old Riding mower 21 hp Briggs & stratton engine . Motor hard to turn with starter ,new starter & battery-It make 3/4 turn & if if make 1 to 2 turn start right up. When starter can not turn it heat up ,without Spark plug engine move ok , I checked the valve clearance .004 & .006 – Do you think it is a Compression release valve ,how I can be sure of that. Please help ,what other thing it could be?

  18. I have a red craftsman riding lawn mower. I turn the key on the motor turns but it wont turn over. i have put in a new spark plug. I have even changed the gas and changed the oil. I have adjusted the front vavles as well. I have even checked the battery and also other items as well. I did rebuild the carburerator as well. I put it all back together and it still doing the same thing. I am wondering could it be my starter or could it be the solenoid as well im not sure. I really dont think its a timing issue at all unless i am wrong. Last for all is i have a video if i can share with someone and then let me know what they think because i am so lost of what else to try out or do thanks very much. This red riding lawn mower is key to what i do in work thanks all

  19. The only thing this guy did not hit on is if you have " No spark " condition is the small kill wire on the ignition coil. If you have no spark, remove that small wire on the coil and try a start the engine… If it starts with the kill wire off, you either a grounded kill wire, bad seat switch, ignition switch,etc.

  20. Rip Sears 19_ _ 2018 2018 was a hard year for me because Sears a toyrus closed the Craftsman still alive it's at Lowes

  21. Awesome video i wish all all "how to" videos were just as this one….keep"em coming and just a suggestion make videos of some other things….i just fixed my riding mower with a new 1ft fuel line, new fuel filter carb cleaner and started fluid….10 stars out of 5.

  22. I had to rebuild my carb when replacing the float needle… Just make sure you mark or take a pic with your phone of your throttle linkage before you disassemble it. If you don't put the throttle cable assembly back how you had it, you can get a similar issue where it has trouble starting and/or the rpms don't go as high.
    Great video. Thanks for sharing!

  23. My rider has a intek 20hp B&S it is hard to start like no fuel, after several times it finally starts but chugs for a few seconds then when I speed up the engine a cloud of white smoke puffs from the exhaust then after warm up a low knock noise from around the flywheel area starts, could be a rod but does not sound like one. What would you suggest to do?

  24. I was mowing hit an ant pile and mower stopped will turn over but not start plug is good has spark has compression had carburetor cleaned gets gas the valves are good but still wont start pls help me I'm out of bc things to try

  25. By far the best video explaining what problem solving should look like .
    Best trouble shooting video ever!

  26. I think I'll just call another serviceman. I called Sears one year and the serviceman that came out told me that the deck was rusted which could cause a hazard so he took my 98.00 service fee after sitting in his truck for 20 minutes and didn't attempt to fix a thing. I'm through with Sears.

  27. What a GREAT SOURCE of information, very well done. This guy is great, extremely knowledgeable.
    Now if only you can get sears parts, which is the challenging part.

  28. It’s SAD that Sears will soon be a relic of the past. An American icon that could have beat Amazon as the worlds largest online retailer if they would have converted their catalogs to digital web pages. Sears has the most sophisticated order fulfillment system in the world. Sears had the infrastructure, just not the right leaders with forward vision to propel the company into the 21st century. RIP Sears.

  29. John Deere lx173 mowed last week then mowed behind trees it just quit cranks won't start but starter fluid it started for a second the quit I guess it was empty on oil dipstick I added oil before I tryed to start it with starter fluid is Motor blown

  30. Thank you for the video. I just changed the oil in my brand new lawn tractor and then it wouldn't start. Turns out I accidentally unplugged the little cellunoid wire while unscrewing the oil filter. Would have taken me forever to find this without your help.

Leave a Reply

Your email address will not be published. Required fields are marked *